Nafees Nazz Construction

Description Dr. Fixit Primeseal is water-based primer composed of acrylic emulsion polymer, properly selected fine fillers, white pigments & additives in water as a medium. It is used as primer over exterior & interior building walls before application of Dr. Fixit Raincoat & other water based paints. Standard Compliance / Specification Meets the requirement of ASTM D 1227 – 87, Type III standard. Areas of Application Priming of plastered walls, asbestos, brick, false ceiling, concrete surface, etc. Features & Benefits } Bonding - Good binding of chalky or porous substrates and over coating. } Suitability - Used as a primer on internal and external surfaces. } Alkali resistant - Based on chemically inert polymers hence suitable for high alkaline substrates. } Penetration - Provides deep penetration thus imparts excellent substrate adhesion. } Efflorescence - Provides excellent efflorescence resistance due to its chemical inertness. Method of Application 1 SURFACE PREPARATION } Surface for treatment must be thoroughly cleaned of all laitance, loose material, oil, grease, etc. } Mechanical means such as wire brushing & shot blasting can be used. } Finally vacuum cleaning of all loose solids and liquids can be done if required. } All surface cracks up to 5 mm width should be filled up with Dr. Fixit Crack X or Dr. Fixit Unifiller. Cracks more than 5 mm and all separation gaps should be filled up with Dr. Fixit Pidicrete URP or Dr. Fixit Unibond SBR modified mortar or as specified. 2 APPLICATION } Dilute Dr. Fixit Primeseal with water in proportion of 2:1 and stir well until a uniform consistency is achieved. } Apply a single coat of diluted Dr. Fixit Primeseal on the cleaned substrate & allow it to dry for 2 to 3 hours before commencing to further finish coats. } Light cut with sand paper the coating of Dr. Fixit Primeseal before commencing the finish coats on internal walls Precautions & Limitations } Only 50% dilution is recommended for Dr. Fixit Primeseal by water. } Excess water on substrate must be removed by suitable means. } Do not apply during rains or in direct sunlight. } Do not tint the primer


Coverage 8-10 m2 / ltr / coat coverage may vary depending upon the nature and texture of the substrate Packing 1, 4, 10 & 20 ltrs. Shelf Life & Storage } Shelf life is 24 months from the date of manufacturing in unopened condition. } Store in a cool & dry place. } Keep away from direct sunlight Health & Safety Precautions } Caution should always be exercised while handling of any chemical products. } Skin Contact: Wash skin with soap & water. Remove contaminated clothes. } On eye contact: Immediately splash eyes with plenty of water. Consult Physician if irritation persists. } Ingestion: Do not induce vomiting. Never give anything by mouth to an unconscious person. Call a Physician. Other Products Categories available Dr. Fixit brings you the widest range of Construction Chemicals

Description Dr. Fixit Pidicrete URP is based on modified styrene butadiene latex supplied as a ready to use bonding agent in liquid consistency. It is used for repair of spalled concrete – floors, columns, beams, chhajas, slabs & waterproofing of toilets & bathrooms, small terraces etc. as it bonds strongly to old & new concrete and to plasters. It reduces shrinkage, prevents cracking, dust pick up & improves abrasion resistance. Areas of Application £  For concrete repairs - Spalled concrete of floors, columns, beams, chajja, slabs, parapets, etc. £ For waterproofing – Small roof terraces, sunken portions of toilets & bathrooms, chajja & lift pits, balconies £ As a bond coat – For bonding of new concrete to old concrete, masonry stone work, plastering. £  For cladding – Fixing or re-fixing of slip bricks, tiles, stones & marble bedding. £ As external rendering – Weatherproof & frost resistant render £  As bonding slurry coat - For pinhole treatment on concrete surface Method of Application £ Mechanically clean the surface to remove all loose particles, dirt, oil, grease etc. Vacuum clean to remove all loose material. £ Economical waterproofing – Mix Dr. Fixit Pidicrete URP with cement in ratio of 1:1.5 by weight and apply in 2 coats. Protective screed is a must £ As repair mortar – Mix Dr. Fixit Pidicrete URP at 10-15% by weight of cement in 1:3 cement-fine sand mix for use as repair mortar along with 20 % water by weight of cement to the workable consistency £ As screed concrete - Mix Dr. Fixit Pidicrete URP 10-15% by weight of cement to a screed concrete of proportion-1:1.5:1.5 (cement:sand:6 mm aggregates) along with 20% water by weight of cement. Mix the content to a uniform consistency £ As bond coat in repair – Mix Dr. Fixit Pidicrete URP with cement in 1:1 ratio by weight & apply on a pre-wetted substrate. Overlay repair mortar when the bond coat is tacky Coverage As a waterproofing coating - 22 – 25 sq.ft./kg in 2 coats As a mortar modifier – 6-7.5 kg of Dr. Fixit Pidicrete URP per 50 kg of cement As a bonding agent – 45 – 50 sq.ft./kg per coat

Features & Benefits:

• Styrene Butadiene co-polymer latex liquid that improves waterproofing
• Strengthens bonding of new and old concrete & plaster
• Enhances strength & water resistance of repair mix - concrete & mortar

Description Dr. Fixit Pidicrete URP is based on modified styrene butadiene latex supplied as a ready to use bonding agent in liquid consistency. It is used for repair of spalled concrete – floors, columns, beams, chhajas, slabs & waterproofing of toilets & bathrooms, small terraces etc. as it bonds strongly to old & new concrete and to plasters. It reduces shrinkage, prevents cracking, dust pick up & improves abrasion resistance. Areas of Application £ ???For concrete repairs - Spalled concrete of floors, columns, beams, chajja, slabs, parapets, etc. £ For waterproofing – Small roof terraces, sunken portions of toilets & bathrooms, chajja & lift pits, balconies £ As a bond coat – For bonding of new concrete to old concrete, masonry stone work, plastering. £ ???For cladding – Fixing or re-fixing of slip bricks, tiles, stones & marble bedding. £ As external rendering – Weatherproof & frost resistant render £ ???As bonding slurry coat - For pinhole treatment on concrete surface Method of Application £ Mechanically clean the surface to remove all loose particles, dirt, oil, grease etc. Vacuum clean to remove all loose material. £ Economical waterproofing – Mix Dr. Fixit Pidicrete URP with cement in ratio of 1:1.5 by weight and apply in 2 coats. Protective screed is a must £ As repair mortar – Mix Dr. Fixit Pidicrete URP at 10-15% by weight of cement in 1:3 cement-fine sand mix for use as repair mortar along with 20 % water by weight of cement to the workable consistency £ As screed concrete - Mix Dr. Fixit Pidicrete URP 10-15% by weight of cement to a screed concrete of proportion-1:1.5:1.5 (cement:sand:6 mm aggregates) along with 20% water by weight of cement. Mix the content to a uniform consistency £ As bond coat in repair – Mix Dr. Fixit Pidicrete URP with cement in 1:1 ratio by weight & apply on a pre-wetted substrate. Overlay repair mortar when the bond coat is tacky Coverage As a waterproofing coating - 22 – 25 sq.ft./kg in 2 coats As a mortar modifier – 6-7.5 kg of Dr. Fixit Pidicrete URP per 50 kg of cement As a bonding agent – 45 – 50 sq.ft./kg per coat

Guaranted Water proofing servise provide by us. Protact yourDescription Dr. Fixit Raincoat is composed of high quality acrylic emulsion polymer, uv resistant & weather durable pigments, properly selected & graded fine fillers, additives & biocides. It is used as a waterproofing & protective coating for exterior walls of the buildings. Typical Application } All types of exterior masonry surfaces, concrete, cement sand renderings, etc. } Applicable on asbestos sheets. } As an anti carbonation coating for concrete structures dream Home from leaks & dampness.

Features & Benefits:

• Waterproofs concrete during the construction stage.
• Improves workability.
• Avoids cracking.
• Protect concrete from corrosion.
• LW+ should be used in concrete, plaster and mortar in all the areas of house.
• Mix 200 ml of LW+ with every 50 kg bag of cement.

Description Dr. Fixit Pidiproof LW+ is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation. Areas of Application Waterproofing of concrete and sand-cement mortars used in } Basements, } Roof slabs and screeds, } Water tanks & water retaining structures, } External plastering, } Bathrooms and balconies, } Sumps and drains Features } Corrosion resistant - Makes concrete more cohesive, hence protects steel better against corrosion } Compatibility – Being a liquid, easily dispersible & compatible with concrete/mortar mixes. } Permeability – It reduces the permeability of water into concrete. } Strength – The setting time and compressive strength of the concrete remains within the specification limits. } Shrinkage – Reduces shrinkage crack development in plaster & concrete. } Workability – Improves workability of freshly mixed cement concrete. } Durability – Increases durability by improving waterproofing of concrete. Packing 200 ml, 1, 5, 10, 20 & 100 litre Method of Application } Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes. } Start addition of 75–80% mixing water & mix for 2-3 minutes. } Dr. Fixit Pidiproof LW+ is added as per the recommended dosage into the remaining mixing / gauging water, then add to concrete mixer & mix for another 2 minutes. } Place the concrete or apply plaster, as needed. } Cure the applied mortar or concrete as per good construction practices. Precautions & Limitations } Do not add Dr. Fixit Pidiproof LW+ directly to dry cement & aggregate mix. } Maintain water-cement ratio as low as possible. } Do not increase the dosage of Dr. Fixit Pidiproof LW+ than the recommendation.


Dosage 200 ml per 50 kg bag of cement Shelf Life } Best before 2 years from the date manufacture when in sealed pack and stored under proper condition. } Store in a cool & dry place. Health & Safety } Use rubber hand gloves & safety goggles, while using Dr. Fixit Pidiproof LW+. } In case of contact with skin, wash with plenty of water. } Keep out of reach of children Other Products Categories available Dr. Fixit brings you the widest range of Construction Chemicals

Features & Benefits:

• Waterproofs concrete during the construction stage.
• Improves workability.
• Avoids cracking.
• Protect concrete from corrosion.
• LW+ should be used in concrete, plaster and mortar in all the areas of house.
• Mix 200 ml of LW+ with every 50 kg bag of cement.

Description Dr. Fixit Pidiproof LW+ is specially formulated integral liquid waterproofing compound composed of surface active plasticising agents, polymers & additives. It is used as an additive for cement concrete, mortar & plasters. It makes concrete cohesive and prevents segregation. Areas of Application Waterproofing of concrete and sand-cement mortars used in } Basements, } Roof slabs and screeds, } Water tanks & water retaining structures, } External plastering, } Bathrooms and balconies, } Sumps and drains Features } Corrosion resistant - Makes concrete more cohesive, hence protects steel better against corrosion } Compatibility – Being a liquid, easily dispersible & compatible with concrete/mortar mixes. } Permeability – It reduces the permeability of water into concrete. } Strength – The setting time and compressive strength of the concrete remains within the specification limits. } Shrinkage – Reduces shrinkage crack development in plaster & concrete. } Workability – Improves workability of freshly mixed cement concrete. } Durability – Increases durability by improving waterproofing of concrete. Packing 200 ml, 1, 5, 10, 20 & 100 litre Method of Application } Charge cement & aggregates to concrete mixer as per the mix design, mix in dry state for 1–2 minutes. } Start addition of 75–80% mixing water & mix for 2-3 minutes. } Dr. Fixit Pidiproof LW+ is added as per the recommended dosage into the remaining mixing / gauging water, then add to concrete mixer & mix for another 2 minutes. } Place the concrete or apply plaster, as needed. } Cure the applied mortar or concrete as per good construction practices. Precautions & Limitations } Do not add Dr. Fixit Pidiproof LW+ directly to dry cement & aggregate mix. } Maintain water-cement ratio as low as possible. } Do not increase the dosage of Dr. Fixit Pidiproof LW+ than the recommendation.


Dosage 200 ml per 50 kg bag of cement Shelf Life } Best before 2 years from the date manufacture when in sealed pack and stored under proper condition. } Store in a cool & dry place. Health & Safety } Use rubber hand gloves & safety goggles, while using Dr. Fixit Pidiproof LW+. } In case of contact with skin, wash with plenty of water. } Keep out of reach of children Other Products Categories available Dr. Fixit brings you the widest range of Construction Chemicals

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

“Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Bekar rod use to fill crack its 15 to 50 rs / meter

Description Dr. Fixit Raincoat Neo is high build water-based elastomeric exterior wall, waterproof coating. Designed with weather resistant acrylate polymers. It is UV resistant and offers good hiding and spreading. Dr. Fixit Raincoat Neo develops a strong inter-coat adhesion with the substrate therefore no separate primer is required. The coating doesn’t peel off from the wall and flake, hence the walls, look beautiful for longer periods. Typical Applications Plastered and rendered vertical wall surface Already painted wall surfaces Features Waterproofing - More durability and a thicker coat than ordinary exterior paint. UV protection - Provides complete weather protection from heat and rain. Anti-algal resistance - Keep your walls fresh for longer time. Crack bridging – Elastic film covers hair line cracks, Long term protection - Backed by 5 year performance warranty. Color Variants – Tintable; available in wide range of colour variants.


Method of Application 1 SURFACE PREPARATION Ensure new cement sand plaster surfaces are completely/cure and dry for 8 - 12 weeks. Clean the surface till it is free from dust, grease and flaking paint. Any unstable paint to be removed, using high-pressure wash or scraper, whichever is appropriate. Algae and fungus on the wall to be removed, by using high-pressure wash or coir brush and shall be treated with fungicidal solution. All surface cracks up to 5 mm width should be filled up with Dr. Fixit Crack-X paste. Cracks more than 5 mm and all separation gaps should be filled up with Dr. Fixit Pidicrete URP modified mortar or as specified. 2 APPLICATION For Vertical Surface Fresh Plaster Or Repainting: Use Dr. Fixit Raincoat Neo directly from the container. Stir contents well before use. Brush / roller apply a self-priming coat of Dr. Fixit Raincoat Neo on the vertical wall surface in SSD condition, diluting 1 litre coating with 100ml clean portable water. Allow it to dry for 4 -6 hours. Apply a coat of Dr. Fixit Raincoat Neo without dilution as waterproof top coat, either by roller or brush with force coverage at the rate of 3.7 - 4.1 Sq mtr / litre to achieve DFT of 100 - 110 microns. Allow it to dry for 4 -6 hours. * Lighter shades of white base on the top of dark colours need additional coat for finishing. An additional coat should be applied in case of horizontal surfaces like the top of windows, ledges, parapet wall, etc. Allow the coating to full air cure for 7 days.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

A. What is ROOF GUARD BLACK

ROO F G UAR D B LA CK is cold applied liquid waterproofing membrane, specially formulated from a blend of special resin and rubber, reinforced with special water repelling fillers, minerals stabilizers and gelling agent.

USES
Ideal waterproofing system for concrete roofs, polyurethane foam slabs, and polyester built up roofs, maintenance of existing roofs, masonry and concrete walls, bathrooms, basements, bridges, decks, metal surfaces etc. Used as a sandwich membrane in new construction and as surface treatment on existing slabs 

B. Why Kwick Fix Solutions is Best Option for ROOF GUARD BLACK

1. KWICK FIX SOLUTIONS purchases material from the core company / factory or its authorised channel only. Hence, KWICK FIX SOLUTIONS sells only orginal & genuine products.

2. KWICK FIX SOLUTIONS has ready stock and fresh material available.

3. KWICK FIX SOLUTIONS is located in the hub of mumbai transport area. Hence, deliveries are prompt. 

4. KWICK FIX SOLUTIONS is a trusted brand and has a reputation of over 120 years in the market. The company is an extension of a 120 year old firm.

Roof Care advance - Waterprooging 635 20 Ltr

“Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Dr. Fixit 132 PRE BOND -E WATERPROOF MEMBRANE NET CONTENT:1 u(24 Mx 20 M)

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Choice Aluminium Silver Paint 4 Ltr.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.

Nafees Nazz Construction” is a distinguished wholesaler offering an enormous consignment of Exterior Emulsion Paint, Cleaning Agent, Bonding Agent etc.